How to add reverb in Audacity
To add reverb in Audacity 4, select the audio and choose Effect ▸ Delay and reverb ▸ Reverb. Adjust Room size, Reverberance and Wet gain, click Preview to listen, then Apply. To try reverb without changing the audio, add it as a live track effect instead.
This guide covers both ways to add reverb, what each control does, starting settings for voice and music, and how to keep reverb from washing out your recording.
Controls and defaults from the Audacity manual for Audacity 4. Shortcuts are written for Mac; Windows uses Ctrl where Mac uses Cmd.
Audacity and reverb on MuseHub
Two ways to add reverb
- As an effect on the audio: Effect ▸ Delay and reverb ▸ Reverb, with audio selected. The reverb is written into the selection when you click Apply.
- As a live track effect: press E to open the realtime effects panel, click Add effect and choose Reverb. You hear it during playback, you can change it any time, and the audio itself stays untouched until you export.
Use the live version while you’re deciding, and the menu version when you want the reverb fixed in one part of a recording.
What each control does
| Control | What it changes | Default |
|---|---|---|
| Room size | How large the simulated space is | 75% |
| Pre-delay | The gap before the first reflections | 10 ms |
| Reverberance | How long the reverb takes to die away | 50% |
| Damping | How quickly high frequencies fade in the tail | 50% |
| Stereo width | How wide the reflections spread | 100% |
| Low tone / High tone | How much bass and treble the reverb has | 100% each |
| Wet gain | The level of the reverb itself | −1 dB |
| Dry gain | The level of the original sound | −1 dB |
| Wet only | Outputs only the reverb, with no original sound | Off |
The effect also comes with factory presets, which you can load from the presets bar at the top of the window.
How to add reverb, step by step
- Select the audio. Include a second or two of silence after it, because the reverb tail continues past the end of the sound.
- Choose Effect ▸ Delay and reverb ▸ Reverb.
- Set the size of the space with Room size and Reverberance: lower for a small room, higher for a hall.
- Set how much you hear with Wet gain. Start lower than you think.
- Click Preview, adjust, and click Apply when it sounds right.
Starting settings
| Use | Room size | Reverberance | Wet gain | Also |
|---|---|---|---|---|
| Spoken voice, subtle room | 20–40% | 20–30% | −10 to −15 dB | Keep it barely noticeable |
| Sung vocal | 50–75% | 40–60% | −6 to −10 dB | Add 20–40 ms of pre-delay |
| Instruments in a hall | 75–100% | 60–80% | −6 dB | Lower High tone for a darker hall |
These are starting points, not presets. Listen in context and adjust.
Keep the words clear
Pre-delay is the control that keeps a voice understandable in a big space. A short gap before the reflections separates the words from the wash behind them.
For more control, put the reverb on a track of its own: copy the voice onto a second track, apply Reverb to the copy with Wet only turned on, and set its level with that track’s volume. You can then EQ, fade or turn the reverb down without touching the original recording.
Common mistakes
- Too much reverb. If you notice the reverb before the voice, turn Wet gain down.
- Cutting off the tail. Without silence at the end of the selection, the reverb stops abruptly.
- Reverb on a podcast voice. Speech usually needs little or none; a dry, close voice is easier to follow.
FAQ
Next steps
For what reverb is and why it works, see what is reverb. For a backwards swell into a note, see reverse reverb and reverse cymbal. The free MuseFX collection from Muse Group adds its own reverb as a live effect in Audacity.
Get Audacity and MuseFX free in one place — download MuseHub free.
